[Из песочницы] Bluetooth-метеостанция на Arduino для начинающих30.12.2015 15:22

int lightPin= 0; //номер входа, к которому подключен фоторезистор
void setup()
{
}
void loop()
{
  int light = analogRead(lightPin);
}

#include 
#include 
#include 
Adafruit_BMP085_Unified bmp = Adafruit_BMP085_Unified(10085);
void setup(void)
{
/* Initialise the sensor */
  if(!bmp.begin())
  {
    /* There was a problem detecting the BMP085 ... check your connections */
    Serial.print("Ooops, no BMP085 detected ... Check your wiring or I2C ADDR!");
    while(1);
  }
}
void loop(void)
{
  sensors_event_t event;
  bmp.getEvent(&event);
  if (event.pressure)
  {
    float pressure = event.pressure;
    
    float temperature;
    bmp.getTemperature(&temperature);

    float seaLevelPressure = SENSORS_PRESSURE_SEALEVELHPA;
    float altitude = bmp.pressureToAltitude(seaLevelPressure, event.pressure); 
  }
}

/* В примере показано использование LCD экрана 1602. */  
#include 
#include   
LiquidCrystal_I2C lcd(0x27,16,2); // Параметры: Адрес устройства, размер экрана  
void setup()
{
    lcd.init();
    // Инициализация lcd
    lcd.backlight();
    // Включаем подсветку
    // Курсор находится в начале 1 строки
    lcd.print("Hello");
    // Выводим текст
    lcd.setCursor(0, 1);
    // Устанавливаем курсор в начало 2 строки
    lcd.print("World!");
    // Выводим текст
}  
void loop()
{ }
// Подробнее: http://xrobot.by/modules/lcd_4_4#ixzz3vQXoFKOj

#include 
#include 
#include   

LiquidCrystal_I2C lcd(0x27,16,2); // Параметры: Адрес устройства, размер экрана  

#define rxPin 2
#define txPin 3

SoftwareSerial btSerial(rxPin, txPin);

bool isDisplayingMode = true;
 
void setup()
{
   lcd.init();
   lcd.backlight();
   // define pin modes for tx, rx pins:
   pinMode(rxPin, INPUT);
   pinMode(txPin, OUTPUT);
   btSerial.begin(38400); 
   Serial.begin(38400);
   Serial.println("Serial started");
   
           
   lcd.print("    Waiting");
   lcd.setCursor(0, 1);
   lcd.print(" for connection");
   
   btSerial.println("AT");
   while (!btSerial.available());
   while (btSerial.available() > 0)
        char c = btSerial.read();
   btSerial.println("AT+INIT");
   while (!btSerial.available());
   while (btSerial.available() > 0)
        char c = btSerial.read();
   btSerial.println("AT+INQ");
   while (!btSerial.available());
   while (btSerial.available() > 0)
        char c = btSerial.read();
   btSerial.println("AT+LINK=2014,5,191146");  
   while (!btSerial.available());
   while (btSerial.available() > 0)
        char c = btSerial.read();   
}

void loop()
{   
  int i = 0;
  char someChar[32] = {0};
  // when characters arrive over the serial port...
  bool availible = Serial.available();
  if(availible) {
    do{
        someChar[i++] = Serial.read();
      //As data trickles in from your serial port you are grabbing as much as you can, 
      //but then when it runs out (as it will after a few bytes because the processor 
      //is much faster than a 9600 baud device) you exit loop, which then restarts, 
      //and resets i to zero, and someChar to an empty array.So please be sure to keep this delay 
      delay(3);                  
 
    }while (Serial.available() > 0);

    lcd.clear();
    Serial.println(i);
    btSerial.println(someChar);
    Serial.println(someChar);
  }
 
  lcd.setCursor(0, 0);
  while(btSerial.available()) 
      {
        if (isDisplayingMode)
        {
          lcd.clear();
          isDisplayingMode = false;
        }
        char c = (char)btSerial.read();
        Serial.print(c);          
        if (c != 13 && c != 10)
          lcd.print(c);
        if (c == '\n')
          lcd.setCursor(0, 1);
      }
}

#include 
#include 
#include 
#include 

Adafruit_BMP085_Unified bmp = Adafruit_BMP085_Unified(10085);
int lightSensorPin = 0;

#define rxPin 2
#define txPin 3

SoftwareSerial btSerial(rxPin, txPin);

struct SensorData
{
  float Pressure;
  float Temperature;
  float Altitude;
  float Lightness;
  void DisplaySensorData()
{
    Serial.print("Light:       ");
    Serial.print(this->Lightness, 2);
    Serial.println("%");
    Serial.print("Altitude:    "); 
    Serial.print(this->Altitude); 
    Serial.println(" m");
    Serial.print("Temperature: ");
    Serial.print(this->Temperature);
    Serial.println(" C");
    /* Display atmospheric pressue in hPa */
    Serial.print("Pressure:    ");
    Serial.print(this->Pressure);
    Serial.println(" hPa");
    Serial.println("");
}

void DisplaySensorDataInTwoRows()
{
    Serial.print("Temp: "); Serial.print(this->Temperature); Serial.println(" C");
    Serial.print("Pr: "); Serial.print(this->Pressure); Serial.println(" Pa");
    delay(1000);    
    Serial.print("Alt: "); Serial.print(this->Altitude); Serial.println(" m");
    Serial.print("Light: "); Serial.print(this->Lightness); Serial.println(" %");
    delay(1000);
}
void SendDataToRemote()
{
    btSerial.print("Temp: "); btSerial.print(this->Temperature); btSerial.print(" C\n");
    btSerial.print("Pr:   "); btSerial.print(this->Pressure); btSerial.print(" hPa\n");
    delay(5000);    
    btSerial.print("Alt:   "); btSerial.print(this->Altitude); btSerial.print(" m\n");
    btSerial.print("Light: "); btSerial.print(this->Lightness); btSerial.print(" %  \n");
    delay(5000);
}
};



void displaySensorDetails(void)
{
  sensor_t sensor;
  bmp.getSensor(&sensor);
  
  Serial.println("------------------------------------");
  Serial.print  ("Sensor:       "); Serial.println(sensor.name);
  Serial.print  ("Driver Ver:   "); Serial.println(sensor.version);
  Serial.print  ("Unique ID:    "); Serial.println(sensor.sensor_id);
  Serial.print  ("Max Value:    "); Serial.print(sensor.max_value); Serial.println(" hPa");
  Serial.print  ("Min Value:    "); Serial.print(sensor.min_value); Serial.println(" hPa");
  Serial.print  ("Resolution:   "); Serial.print(sensor.resolution); Serial.println(" hPa");  
  Serial.println("------------------------------------");
  Serial.println("");
  delay(500);
}

void setup(void) 
{
   // define pin modes for tx, rx pins:
   pinMode(rxPin, INPUT);
   pinMode(txPin, OUTPUT);
   btSerial.begin(38400);
   
  Serial.begin(9600);
  Serial.println("Pressure Sensor Test"); Serial.println("");
  
   
  /* Initialise the sensor */
  if(!bmp.begin())
  {
    /* There was a problem detecting the BMP085 ... check your connections */
    Serial.print("Ooops, no BMP085 detected ... Check your wiring or I2C ADDR!");
    while(1);
  }
    
  /* Display some basic information on this sensor */
  displaySensorDetails();
}
int counter = 0;
void loop(void) 
{
  /* Get a new sensor event */ 
  sensors_event_t event;
  bmp.getEvent(&event);
  SensorData data;
  /* Display the results (barometric pressure is measure in hPa) */
  if (event.pressure)
  {
    data.Pressure = event.pressure;
    
    float temperature;
    bmp.getTemperature(&temperature);
    data.Temperature = temperature;

    /* Then convert the atmospheric pressure, and SLP to altitude         */
    /* Update this next line with the current SLP for better results      */
    float seaLevelPressure = SENSORS_PRESSURE_SEALEVELHPA;
    float altitude = bmp.pressureToAltitude(seaLevelPressure, event.pressure);
    data.Altitude = altitude;  
    
    int lightValue = analogRead(lightSensorPin);
    float lightValueInPercent = 1.0 * lightValue / 1024 * 100;
    data.Lightness = lightValueInPercent;
    
    //data.DisplaySensorDataInTwoRows();    
  }
  else
  {
    Serial.println("Sensor error");
  }
  Serial.println("");
  data.SendDataToRemote();
}